Reference: UCF031
Brand: Under Cover Fabworks
UCF 14 Bolt Truss System
A rock-solid upper link mount for your GM Corporate 14 Bolt. No welding to the housing required.
619620081698
Strengthen your high-pinion Dana 30 front housing with a lightweight 16 lb truss.
Strength for the high-pinion Dana 30.
The truss you've been asking for. The main body is 1/2" steel plate that spans over the casting and welds to the top of the center section in two places. It also welds to the driver-side lower coil spring mount and to a 1/4" formed steel channel that spans the axle tube from the truss body to the passenger-side lower coil spring mount.
What's included: Truss body, 1/4" thick channel and passenger-side upper link mount. Hardware is not included.
Install notes: cutting and welding are required. Some clearancing of the driver-side upper control arm bracket end may be needed to clear the truss body. We kept the truss as thin as possible in this area, but some control arms may still interfere.
Fitment: factory high-pinion Dana 30 front axles from the 1984–1999 Jeep Cherokee XJ and 1986–1992 Jeep Comanche MJ, and Jeep Wrangler TJ and Wrangler Unlimited LJ that have had an XJ high-pinion Dana 30 swapped in.
Does not fit the stock low-pinion Dana 30 found in the TJ, LJ, YJ, ZJ, WJ and 2000–2001 XJ. Some late-1999 XJs also came with the low-pinion axle.
Not sure which you have? Look at the pinion where the driveshaft connects. On a high-pinion axle it sits above the axle centerline; on a low-pinion axle it sits below.
Install instructions: see the Attachments tab above, or download the UCF Front Truss System Install Guide (PDF).
Not sure which truss fits? See our Axle Truss Selection Guide.
Specific References
Install instructions for UCF high-pinion Dana 30 and JK Rubicon Dana 44 front truss systems.
Download (154.33KB)Reference: UCF031
Brand: Under Cover Fabworks
A rock-solid upper link mount for your GM Corporate 14 Bolt. No welding to the housing required.
Reference: UCF092
Brand: Under Cover Fabworks
A rock-solid upper link mount for your Ford 8.8" rear axle. No welding to the cast center section.
Reference: UCF035
Brand: Under Cover Fabworks
Upper link and double-ended steering ram mount for your leaf-sprung Chevy/GM Dana 60 front axle. No welding to the cast center section.
Reference: UCF590
Brand: Under Cover Fabworks
A rock-solid upper link mount for your Dana 35 rear axle. No welding to the cast center section.
Reference: UCF579
Brand: Under Cover Fabworks
A rock-solid upper link mount for your Ford Sterling 10.25" or 10.5" rear axle. No welding to the cast center section.
Reference: UCF058
Brand: Under Cover Fabworks
A rock-solid upper link mount for your Dana 60 rear axle. No welding to the cast center section.
Reference: UCF520
Brand: Under Cover Fabworks
Strengthen your JK Rubicon front Dana 44 housing with a lightweight 18 lb truss.
Reference: UCF057
Brand: Under Cover Fabworks
A rock-solid upper link mount for your Dana 44 rear axle. No welding to the cast center section.
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
UCF High-Pinion XJ/TJ/LJ Dana 30 Front Truss System
Strengthen your high-pinion Dana 30 front housing with a lightweight 16 lb truss.
* Required fields
Review sent
Your review cannot be sent
Strengthen your high-pinion Dana 30 front housing with a lightweight 16 lb truss.